![]() If you have any questions regarding export control, please send an email to information in this document was created from the devices in a specific lab environment. For more information, refer to the Bureau of Export Administration web site. It is your responsibility to know the law regarding export of encryption technology. Note: Encryption technology is subject to export controls. This product has advanced VPN features, unlike the Cisco Secure VPN Client 1.x. The information in this document is based on these software and hardware versions:Ĭisco VPN Client 4.x. There are no specific requirements for this document. Refer to Configuring IPsec Between a Cisco IOS Router and a Cisco VPN Client 4.x for Windows Using RADIUS for User Authentication to configure a connection between a router and the Cisco VPN Client 4.x using RADIUS for user authentication. Refer to IPsec Between a VPN 3000 Concentrator and a VPN Client 4.x for Windows using RADIUS for User Authentication and Accounting Configuration Example to establish an IPsec tunnel between a Cisco VPN 3000 Concentrator and a Cisco VPN Client 4.x for Windows using RADIUS for user authentication and accounting. Refer to PIX/ASA 7.x and Cisco VPN Client 4.x for Windows with Microsoft Windows 2003 IAS RADIUS Authentication Configuration Example to set up the remote access VPN connection between a Cisco VPN Client (4.x for Windows) and the PIX 500 Series Security Appliance 7.x using a Microsoft Windows 2003 Internet Authentication Service (IAS) RADIUS server. For more information on how to configure AES, refer to How to Configure the Cisco VPN Client to PIX with AES. The VPN Client supports key sizes of 128 bits and 256 bits only. The VPN Client supports Advanced Encryption Standard (AES) as an encryption algorithm in Cisco VPN Client release 3.6.1 and later and with PIX Firewall 6.3. In order to see the TACACS+ and RADIUS configuration for PIX 6.3 and later, refer to TACACS+ and RADIUS for PIX 6.3 and PIX/ASA 7.x Configuration Example. Vpngroup homeboy default-domain kendall.This configuration example demonstrates how to connect a VPN Client to a PIX Firewall using wildcards, mode-config, the sysopt connection permit-ipsec command, and extended authentication (Xauth). Vpngroup homeboy wins-server 192.168.99.3 Isakmp policy 20 authentication pre-share Timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00Īaa-server radius (inside) host 192.168.99.3 (password) timeout 10Ĭrypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmacĬrypto dynamic-map outside_dyn_map 20 match address outside_cryptomap_dyn_20Ĭrypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-MD5Ĭrypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_mapĬrypto map outside_map client authentication radius Static (inside,outside) tcp interface 0 0Īccess-group outside_access_in in interface outside Static (inside,outside) tcp interface smtp mailhost smtp netmask 255.255.255.255 0 0 Nat (inside) 0 access-list inside_outbound_nat0_acl The ipsec config is to allow me to connect from outside and hopefully isn't going to affect what I am trying to do.Īccess-list outside_access_in permit tcp any interface outside eq smtpĪccess-list outside_access_in permit tcp any interface outside eq sshĪccess-list outside_access_in permit tcp any interface outside eq 3389Īccess-list outside_access_in permit tcp any interface outside eq 255.255.255.0 192.168.99.192 255.255.255.224Īccess-list outside_cryptomap_dyn_20 permit ip any 192.168.99.192 255.255.255.224 I'll check CCO and see how to do allow it. I haven't done anything to allow ESP inbound on PIX_1.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |